Gunco Forums banner

12GA FH--Hairy Shotgun/Rifle--

57K views 425 replies 20 participants last post by  hubel458 
#1 ·
Some info you all may find interesting
in our 12GA FH testing and experimenting.
I'm visiting here and passing it on.Nice site here.
There are two videos of our 12GA FH on YouTube,
exploding big heavy walled plastic pails of water.
Not milk jugs , but 6 gal water in thick
plastic. with thick locked on lids........
The "Grampa's Cannon" one with a long view,
and "Grandpa's First Shot" a closeup video,
the first one, that shows how the top of heavy
shelf got bent. Later kids will do film videos showing
muzzle blast and recoil. We also have tested an
8GA FH, we made on an Enfield bolt action.
Also 3 ought buckshot from the 8ga load
goes through 2" hardwood ok. I will test
8ga on waterpail also, to see what happens. Ed
 
#103 ·
Shot the NEF 8GA FH. That is the heavy barrel NEF
that was a 10ga.. I bored it out to 8ga and chambered
it for the heavy duty 8ga case. 770gr at 2200 out of
29" barrel. End of barrel has internal brake with 24
porting holes and with weighted thumbhole stock,
it handles recoil easy.Will have picture soon.Ed
 
#104 ·
Here is my 12GA FH Savage 210 with thumbhole
stock, I put on in place of first one that cracked.
Along with weight and heavy barrel handles recoil
great. It is a Boyd and came inleted for Savage
112, and I re-did inleting to fit 210 and
heavy barrel,and got rid of monte carlo
outline.Ed

 
#106 ·
4227 is just a powder with a certain burn speed like all the rest.
Its relative speed is about 250, the fastest shotgun powders are
about 7-800, 4831 rifle powder is about 100, the slowest bmg
powders about 70. All powder has about same energy per grain.
We can use so much more of the 4227 as it is slower in a much
bigger bore than a pistol.And 775gr slug is light for an 8ga.If you used
1500gr then you'd cut powder back about 2/3 as much.We lab tested
90gr 4227 in 12ga with 600gr slug and average of peak pressures
was under 15,000 psi. That is like some magnum factory slug loads,
of same slug weight,only we get 3-400 fps more. Not because of any
higher peak pressure, but due to slower burn rate powder the average
pressure the full length of the barrel is higher, thus more velocity.
And it takes more of slower powder to keep that barrel pressure
average higher. But we use this as a gimmic to get more velocity
without fear of to high peak pressure.I that load was the fastest
shotgun powder it would spike to over 100,000 psi.

Here is picture of RIP's two 12GA FH NEFs.
Both are the 12ga Ultra Slug Guns.
One has Vias brake, other expansion chamber.
He calls it his golf ball launcher. Ed


 
#107 ·
I found a shotgun primer that will ignite rifle powders,
like RL15-19, IMR 4064,4198, etc. With regular shotgun
primers I had to use Blue Dot starter.
But not with these.....They are the industrial
shotgun primers used in the 8ga kiln gun cases. I use
these cases with basecup reduced in my 8 gauges.
When I set up first 8ga I fired the primers only to test
firing function(cases came with primer), then I put
regular 209 primers in to test loads, with 4759 powder.
Found box of WIN paper case kiln 3oz loads and took one
apart and noticed it had 94gr of some ball powder.
I wondered what powder is and how a regular shotgun primer
could ignite that, based on our need for starter powder
using regular rifle powders. So I fired that industrial
primer and flame and sparks came out of 8ga NEF barrel
2-3 feet. Put a regular primer in same case and flame
just a few inches. So I took REM kiln case with original
REM industrial primer and 2-3 feet of flame,and put regular
primer in and just few inches of flame. If anyone got
info on th powder used and how to get these primers,
let us know. I took some out of 8ga and put in 12ga plastic.
Using these hairy industrial primers today fired 180gr
of RL-15, in 12GA FH NEF, in 3.5" plastic cases with
437gr Brenekke KO slug. Got perfect ignition, no starter.
140gr with 600gr dixie, perfect ignition.
Also I have the 12ga Encore that we tested loads
in, on Gunbroker, in shotgun singleshot section.Ed
 
#108 ·
I always felt that if some company would make powders like 7383
available it would be great. 7383 ignites fine with regular
shotgun primers in 12ga, but it is surplus and only a few of
us have it.It is a powder that has a lot of the deterrent inside
the of the material, not all near the outside like 99% of
all other powders whether spherical, tubular, or flake.
This allows easier ignition, but yet the deterrent still can
control the speed. Well the new RE-17 just out for 2 days
is setup like that. The surface of the RE-17 grains is
more porous than RE15, so that fact allows better ignition
even though a slower powder, and along with fact that company
got most deterent inside it still regulates speed.
Today I fired with regular REM and WIN primers in
plastic and RMC cases, a whole bunch of loads of RE-17,
with no hesitation or squibs or misfires. Loads ranged from
437 gr slugs to 750gr slugs today. All loads burnt clean
and I got in RMC case one of RG's 715gr jkt slugs to 2300
with 160 gr of RE-17. Using plastic you must have a strong
roll crimp with slug and wads tight.....Whoopee....Ed
 
#109 ·
I shot couple loads with regular primer with RE-17
and 1040 gr slug in 12GA FH NEF, and it does great.
Tested loads that were cooled outside a while.Perfect ignition.
I fired loads RE-17 8ga plastic,in my 8GA FH on new NEF long
heavy barrel that was a 10 ga and RE-17 is great. No hesitation,
it fires off as good in 8ga as the 4759. Remember
I couldn't get good ignition in 8g with 4227, but so far
RE-17 is magic. In 8 ga all it would hold under the 8ga REM
wadcup with 770 gr slug is 200 gr of RE-!7, with the
wadcup pressed down, compressed real hard,good crimp,
and it really bellers.2400 plus.Going by case
expansion about 20k pressure. Which don't bother
those one piece compression molded super strong
8ga REM cases. You must have real tight proper
roll crimp in plastic cases and good tight
taper crimp or rolled in crimp in groove
in the brass cases. In RMC brass I size it so slugs
have to be shoved in with press.In all of this
brass and plastic, no airspace use wads when needed.

And this RE-17 doesn't break up the kernels when powder
gets to a certain point, like the 7383 does, causing burning
rate to speed up more than what it was designed for.
I tested 7383 in my 700HE, and when up to 35-40k it's
pressure went up fast, much more than linear progression.
I still like 7383 at shotgun pressures, but I really like
RE-17.Just great fun to use slower powder, so that
we don't have to worry about fast, high peak pressures,
but yet get large volumne, pressure curve for good velocity.

Ok- for those who want to get into the 12GA FH and get
the long strong 3.85 inch cases Rob on AR got some made,
email him to deal to get some- garnickrob@aol.com
He can also tell you where to get reamer.Ed.
 
#111 ·
Here's picture of solid turned 12ga slugs that Rob makes.
They are flat on one end and hollowpoint on other.
They can be shot either direction. Aluminum ones
are 346gr, brass 1080gr........If you need any
contact him. He, RIP, and others on AR are testing
them with different powders. I have gotten similiar brass
ones to 1900 in NEF with RMC case, with
140 gr the new RL-17. Ed
 
#112 ·
Heavy brass slug testing-----
RIP'S components in first picture-
15gr Blue Dot starter, thin plastic separator,
230gr HBMG, thin plastic under slug,
and 1087gr brass slug; in a RMC 3.5"
brass case, fired in his great looking,
braked NEF 12ga FH Ultra, got him
1812 fps average. Barrel and brake
are 27" total length. Great work. Ed



 
#113 ·
One of our testers, Bret in MN, got the BPI Sabot with
500gr Hornady .500 slug up to the good speed listed
on BPI"s loading sheet, using shotgun powders. I could
get them there with my loads using much larger amounts
of rifle powders. He tested 3.5" Federal plastic cases in
his Savage 210 with 3.5" chamber and the 28" heavy barrel
he put on. With 50gr of Longshot(max load for all modern
guns) he got 2550 fps, with 500gr in sabot. He use two
BPGS gas seals fitted together over the powder, then
a FS12 Flexseal wad, then a 1/4" cork wad, then the sabot.

Then a good strong roll crimp with drill/drillpress crimper.
This load is at mag shotgun pressures by case expansion
measurements and BPI's 46gr load tested at 12,500 psi.
He also did one with one BPGS and two Flexseals and had
200 fps less.He had tried other combinations seals/wads
and with same amount of powder and got lower yet.
He also went up with the powder, with seal/wads that worked
the best and got about 3000 fps, but the plastic cases
stuck and wouldn't eject easy. I will be testing same
seal and wad column in a few days, in my NEF with long
barrel to compare results.I thank Bret, he is a real
good experimenter and idea man. Everybody is trying
like crazy to get that 500gr saboted slug up to big
game gun velocities with shotgun powder and thanks to
BPI"s supply of the right components it has happened.Ed
 
#114 ·
Hey Ed! I got one! Let the games begin! :D The only thing I want to do for starters is get a 1000 grain slug like in your pic...



And yes, I know this is a 600 grain slug, but this is the cartridge type I'm looking for - all brass (converted .50 BMG) and a slug crimped on the end. Time to re-read all the info now! Here's mine alongside my limited-edition series 10/22:



 
#115 ·
Ed, I have three questions after reading the thread again:


First, do you know the status of Rob's stamped rims for the converted .50 BMG brass? I'd like to purchase some!






Second, I am interested in what I can load the NEF with when using long brass 3.85" case, with large primers? Like the one in this pic:



This is from Page 6 where you state this is RG's Jacketed 715 gr slug. I have some swaging equipment and can press my own jacketed slugs! What kind of load would you recommend for a 1000 gr slug / 3.85" full brass / large primer?





Lastly, when you say "large" primers, are you talking about SHOTGUN primers, Large RIFLE primers, or BMG primers?




Thanks!
- Jerry
 
#116 ·
Jerry- Nice looking NEF you have there.When I say large primers
I mean BMG primers. Rob can make rims or completed cases
and is selling them now. Rims aren't cheap, I think they are
about 5 dollars..Contact him at email given above.
Loads -With long case, bmg primers, you can use 240 grains
of slow HBMG powder.Start at 240 and if it extracts ok, work up.
Always fill up spage with seal and wads.Cushion wad is good.
Here is a Rob project that will make you drool.
Rob on AR is building a 12GA FH double on a Zabala Double
10 gauge frame. It has the Greener crossbolt. He cut off
barrels to make a 4" long monoblock double to screw a
pair of heavy 12ga rifled Pacnor barrels into. He reamed out
monoblock section and threaded it. His barrels are
1.116" at the breach, .97" at muzzle and 22" total length.
Barrels threaded into monoblock with a 15/16" x 32 thread.
In the pics it is partly done and he will put in the ribs
and integral sight rib and regulate for accuracy.
It will be about 14.5 lbs when done he says.Ed



 
#117 ·
Some more BPI seal and sabot testing.
First of all both Bret and I have heavy tight fit barrels
and his barrel on the Savage is faster twist so it took
him 50 gr of Longshot to get what BPI got with
looser barrels and slow twist at 46 gr of Longshot.
For non heavy barreled guns only go to 46 gr.
I did a bunch of tests in my NEF long barrel with long
chamber. My store didn't have any 500gr .500" XTP slugs
so I used some 420gr .512" dia lead Great plains in the
BPI sabot. Using 2 BPGS powder seals, a BPI Flexseal, a
cork wad in 3.5" new Federal cases, roll crimped, I got
2800 fps with 420gr slug. I tried 4 other powder seals,
2 cards, a Remington, a Win, and a odd one, all with the
Flexseal and lost velocity. I fixed up my crimper so it would
roll the plastic down and over inside edge of sabot, as before
it would turn plastiC in too sharp and get some of the crimp
outside the sabot top. If sabot was too low so that the plastic
crimp went clear down to the slug I got high pressure signs.
I also did same loads in used 3.5" REM cases ok.
Now, I thought I should have more velocity, so I swaged the
.512" 420GR slug down to .500" like they say the sabot is for,
AND I GOT OVER A 120 FPS MORE. Everytime. I also used
Alliant Steel powder and got all the same results, using
60gr. It is easier on cases. I also substituted the doubled up
BPGS powder seals and the Flexseal with 520gr Lyman in
place of the seal and cushion on the WW12 wadcup the Lyman
fits in, with some RL-17 loads, of 150gr, and got over 200fps more
that the original WW12 wadcup gave with the Lyman.

Velocity secret is to have the perfect sealing setup with
slug/sabot combo that is NOT too tight. Only tight enough
to get accuracy. The cork seems to protect the sabot
base ok on the shotgun powder loads, and not needed
on the RL-17 loads, which is a easier accelerating powder
and without cork helps make room for the RE-17. I think I
will get increases in the brass RMC cases, with RE-17, with
the BPGS doubled and a Flexseal in place of cards and wads.
We will know soon.Ed
 
#118 ·
OK where do I get reasonably priced 50 BMG brass? I am obviously a huge DIY kind of guy and the only brass I can find online is in lots of 50 or more! I think perhaps 12-20 rounds is all I'd need for a fun range day! Wondering if you guys get your brass new or once-fired?
 
#119 ·
You probably wil lhave to get 50. We try to get unfired
with bullets pulled out. Some shops sell new.Did you get
set up to put rims on cases....If you get used
do a good job annealing.
Here is picture of the breach of 8ga FH NEF with
case in it, to show that the gun is strong enough
for 8ga. I was a 10ga NEF. Has 29" effective barrel
length, and the internal expansion step at muzzle
for the ports that stops muzzle climb and reduces
recoil. Which along with thick pad and thumbhole
stock makes for easy shooting.Ed

 
#120 ·
Here is picture of a 12ga size drawn brass case that was
made back in the 80s. Case is for the CAWS weapon system.
Case is belted, and it and the gun operated at 25,000 psi.
Its bore size is between 12 and 10 ga size, but the od of
the drawn case would let it start in 12ga chambers, so
they added belt so it couldn't go all the way in
to regular shotguns. Notice the thick sides and corner
near the base.Heavy enough for 25,000 psi. They loaded
it with big buckshot and tested other projectiles also.
They had a plastic card over shot and filler and rolled
over brass mouth for crimp. Ed

 
#121 ·
Here is picture of a NEF breach barrel section that I threaded
monoblock style for a .585" cal barrel, to make a NEF 585HE.
It goes on a SB2 10-12ga alloy, super strong frame. Its
OD is 1.210" and the barrel that screws into it will be tapered
to match contour and it will be 1.00" at muzzle, at 32" long.
I know these are strong enough as my 8GA FH testing shows..
Later will do couple more with heavy barrels for 28GA FH, etc,
as all the break action 28 gauges I've looked at have too
thin of muzzles for our slower, powder loads.I'll have 3 of these
that fit one SB2 frame I have here.This makes switch barrels
big power fun.Ed.

 
#122 ·
I fired mono-blocked NEF this week with a 585HE 32"
barrel and the gun is weighted to 15 lbs. Thick pad.
I have cone breech as this case is belted with thick base.
I'll have a pic of gun later. Gun is still tight after testing.
I can take out cases with my fingers as they don't stick.
First 650gr, with no extractor. The HBMG, WC-860,AA8700,
Retumbo, Magpro, RE25, W-780 loads come out of the chamber,
with my fingers.If I tip gun up they fall out.
Top speed with RE25 and W-780 is over 2400. Now I knew what
to load them at because I have tested this case in 3 other guns.
I have all the different powders and bullets tested.
This is example of a case extracting easy,
due to proper side taper that my 585 has....Ed
 
#124 ·
I found odd steel block with a square cornered
1.0" by 1.5" hole through it. It solves a big
machining problem for me in doing a 4bore.
And I happen to have some 1" by 1.5" steel.
The rest of machining I can do, and I have
the levers, hammer, trigger, etc. But the parts
and layout are not going to copy the Wickcliff.
To many problems with all the parts riding on the
breachblock and the crowded stubby extractor.
Will be my own design with hammer and
trigger behind breachblock. An extractor similiar
to Ruger and its shape a cross between WIN 1885
and a Farquarson.In pic you can see drawn outline
on the block of the shape it will have.ED

 
#125 ·
Here is the finished NEF mono-blocked gun with
the 585 barrel, 32" long, 1 to 22 twist.
Chambered for my 585HE belted case.
I used a SB2 10ga action which is same as the 12ga
Ultra actions.I cut it off to make a 4" long monoblock.
and threaded it 1 inch by 14tpi. I'm going to do extra
ones 28GA FH,others.. My 585 is best 585,as the info will
show. I have a 45-70 extractor coming to rework for it.
I am firing first bunchs of test loads without
an extractor, and loads with 650 gr bullets at 2450 and
750 gr bullets at 2250 didn't need the extractor. They
come out with my fingers. Over 8000 ft lbs.I got thumbhole
stock now, because those with higher velocities of 2-400fps more,
were harder to hold on to grip. Trigger guard banged the fingers.
And higher velocity cases come out with a pry from my thumbnail.
Here is picture of rear of gun and the fixins(bullets/cases).
You see a fired case in the chamber, and I have cone breach
setup so that case is in same relationship to chamber as it
is in my three 585HE bolt guns. And is why I can get cases
out with my fingers.OR tip gun up. The hairier loads of
650 at 2650, 750 at 2450 is 10,000 ft lbs. Ed

 
#126 ·
Here's pic of my to be 4bore falling block with
the block to be the breech setting in the hole.
Breach needs trough on the top yet, but now
it is done for exact width and height and the
bottom recess and link hookup is done, since
the picture was taken..Ed

 
#127 ·
The falling block is coming along. I'm not copying my
first models that were a scale up of the Wickcliff.
Complete new design, mainly in shape and type of stock
used, the bridge and reciever setup, and trigger/hammer
behind the block. Block will have no curved outside
shapes, front to back. Pics soon with the stock......

Used wadcutter style 8ga slug made by cutting off part
of a long nosed one in picture, in my 8ga with RE-17
powder.. Over 2300 fps. Slug is a zinc slug from kiln
gun factory load. With nose cut back and hollow I put
in the base it was 800 gr. It had a .20" wadcutter nose
on it.Good tribute to Elmer. The other ones in picture,
just with nose cut off and solid base and is 870 gr.Ed

 
#128 ·
Another couple months maybe 4 bore/ga will fire.Just have a
chunk of shaft on front to simulate barrel to
get a stock fit. Got to profile barrel, thread barrel,
fit in hammer,trigger, couple bottom bolts into action,
design and mount extractor.. some springs, firing pin, etc.
May change/lengthen fulcrum on lever so it doesn't have to
move so far. Lever is held closed by little feramic magnet
in grip. Checking on different shapes for lever. When breach is
lowered the lever stays open due to weight of breach
block. Block moves smooth, no rattling around.
Guys-,I need some Vulcan 50cal V-50 thumbhole laminated stocks.
If there are any used extra ones around let me know.
This way of doing a FB in one piece thumbhole stock will work
for 12GA FH with an action about a 1/4" narrower.ED



 
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top