Page 2 of 4 FirstFirst 1 2 3 4 LastLast
Results 11 to 20 of 31

Thread: KP-44/PPS-43 flat bending jig

  1. #11
    No Hope For Me Coils's Avatar
    Join Date
    Feb 2005
    Location
    PA Where the Amish Roam Free
    Posts
    13,673
    Feedback Score
    38 (100%)

    Default

    bubbamauser that looks good, I'll keep an eye on this thread
    "Government is not the solution to our problem, government is the problem" Ronald Reagan

  2. #12
    Gunco Veteran Viper Dude's Avatar
    Join Date
    Feb 2005
    Posts
    1,683
    Feedback Score
    0

    Default

    Thanks guys, cool thread !!!!

    VD

  3. #13
    Gunco Veteran muttman's Avatar
    Join Date
    Dec 2004
    Location
    west, TN.
    Posts
    1,172
    Feedback Score
    0

    Default

    A bump and a thanks for posting, just need the dems. On the jig. Muttman

  4. #14
    Gunco Regular bubbamauser's Avatar
    Join Date
    Mar 2006
    Posts
    393
    Feedback Score
    1 (100%)

    Default

    Todays progress
    I modified an ak FCG to work without a cut out in the receiver top. an offset was required between the hammer and trigger to make mine work. I opened up the bottom for the trigger to drop through a bit and moved the hammer hole up above the lower sheet metal for spring clearnce and after major grinding on the bottom and lower rear of the hammer also the hammer needs to be thinned a bit to fit in the receiver shell same with the hollow pin for the trigger and sear, FCG is tapco double hook butchered excessively ;D I egged the hell out of the holes too but that will be fixed later








    Muttman,

    There really arent any dimensions to the jig I cut 2 pieces of 1" steel pipe larger than the receiver and then cut 1, 3/4 piece of pipe for the die. I then welded 1 piece of 1" pipe to angle iron at either end then spaced the 3/4 off of the welded side and the soon to be welded side with 14 guage sheet metal (my flat material) 1 on either side and then welded the other 1" piece to the angle iron.
    Last edited by bubbamauser; 03-31-2011 at 04:37 PM.

  5. #15
    Gunco Regular bubbamauser's Avatar
    Join Date
    Mar 2006
    Posts
    393
    Feedback Score
    1 (100%)

    Default

    I had to go back and mod the hammer a bit more it was just clearing and at times hit so I cut a slight angle beside the hammer ear (thats what it looks like) so it kind of matches the receiever profile


    Sear Contact

  6. #16
    Gunco Veteran muttman's Avatar
    Join Date
    Dec 2004
    Location
    west, TN.
    Posts
    1,172
    Feedback Score
    0

    Default

    bubba,
    I just got done making a jig using 1" O.D. pipe, and bent a flat. good find, easy and quick. photo and wright up latter.
    what are you planing on using for a boldt blocker per the ATF?
    muttman

  7. #17
    GuncoHolic Rahatlakhoom's Avatar
    Join Date
    Jan 2005
    Location
    Indiana
    Posts
    2,315
    Feedback Score
    14 (100%)

    Default

    Great jig set up.
    thanks!
    Charter member-Busted Box Club est. 2006

    "I will adhere to the Patriot Act, the one signed in 1776"
    - Marc Anderson

  8. #18
    Gunco Regular bubbamauser's Avatar
    Join Date
    Mar 2006
    Posts
    393
    Feedback Score
    1 (100%)

    Default

    Muttman,

    I am going to weld a piece of 1/4 drill bit shank through the receiver before the trunnion so I wont have to cut a slot all the way back on the bolt ( I suffer from mill envy)

    Rahatlakhoom,

    I follow and use all the info you post on your builds, so thank you
    Last edited by bubbamauser; 04-04-2011 at 11:37 PM.

  9. #19
    Gunco Regular bubbamauser's Avatar
    Join Date
    Mar 2006
    Posts
    393
    Feedback Score
    1 (100%)

    Default

    Tonight I tacked the pieces together to see what I had to adjust next. The tacks were done with an arc when its complete it will be cleaned up with mig. i have a lot of "adjustments" to make


  10. #20
    Gunco Veteran muttman's Avatar
    Join Date
    Dec 2004
    Location
    west, TN.
    Posts
    1,172
    Feedback Score
    0

    Default

    looking good.

Page 2 of 4 FirstFirst 1 2 3 4 LastLast

Search tags for this page

bend jig for pps43 flat

,

jig for pps 43

,
kp44 build
,
pps-43 flat bending
,
pps43 bending jig
,

pps43 reciver jigg

Click on a term to search our site for related topics.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •