Page 15 of 24 FirstFirst ... 5 11 12 13 14 15 16 17 18 19 ... LastLast
Results 141 to 150 of 233

Thread: Polymer 80% lowers

  1. #141
    No Hope For Me Coils's Avatar
    Join Date
    Feb 2005
    Location
    PA Where the Amish Roam Free
    Posts
    14,039
    Feedback Score
    38 (100%)

    Default

    I looked at the HF ones and they seemed rather sloppy and with huge amount of play
    Yes they do, but I did buy one. You need to adjust the tension screws on the sides so they are just tight enough to hold it in place but it still moves when you crank the handles. It's not great but for the price it's decent
    "Government is not the solution to our problem, government is the problem" Ronald Reagan

  2. #142
    3/6 Infantry mtdew's Avatar
    Join Date
    Jul 2005
    Location
    Benton,AR
    Posts
    2,782
    Feedback Score
    3 (100%)

    Default

    Quote Originally Posted by Chiroone View Post
    Dew, where did you get your cross slide drill press vice? I looked at the HF ones and they seemed rather sloppy and with huge amount of play
    Chiroone, I ordered a Grizzly, the reviews were much better. And they cost less!
    "NA BEAN DON CHAT GUN LAMHAINN"
    Clan MacPherson
    "CREAG DHUBH"!

  3. #143
    3/6 Infantry mtdew's Avatar
    Join Date
    Jul 2005
    Location
    Benton,AR
    Posts
    2,782
    Feedback Score
    3 (100%)

    Default

    Quote Originally Posted by o.d. ak View Post
    according to this post from EP over at calguns ther will not be any more blems for sale -


    https://www.calguns.net/calgunforum/...&postcount=285
    Well that's sad. I was saving a few pennies to get however many more I could afford.
    "NA BEAN DON CHAT GUN LAMHAINN"
    Clan MacPherson
    "CREAG DHUBH"!

  4. #144
    AKAHOLIC o.d. ak's Avatar
    Join Date
    Jul 2006
    Location
    South West Missouri
    Posts
    1,584
    Feedback Score
    3 (100%)

    Default

    Quote Originally Posted by mtdew View Post
    Well that's sad. I was saving a few pennies to get however many more I could afford.
    yeah it is a bit disappointing. even with the issues $35 was a decent deal. for $100 ill just get a forged 100%

  5. #145
    3/6 Infantry mtdew's Avatar
    Join Date
    Jul 2005
    Location
    Benton,AR
    Posts
    2,782
    Feedback Score
    3 (100%)

    Default

    Quote Originally Posted by o.d. ak View Post
    yeah it is a bit disappointing. even with the issues $35 was a decent deal. for $100 ill just get a forged 100%
    ditto
    "NA BEAN DON CHAT GUN LAMHAINN"
    Clan MacPherson
    "CREAG DHUBH"!

  6. #146
    Moderator Chiroone's Avatar
    Join Date
    Feb 2004
    Posts
    1,121
    Feedback Score
    5 (100%)

    Default

    Dew,

    Which one of the XY cross tables did you get a Grizzly?
    Last edited by Chiroone; 11-01-2013 at 09:58 PM.
    Nemo ME Impune Lacessit
    Manus sapiens potens est
    пиштоли не убиваат луѓе, тие само го прават тоа полесно

  7. #147
    Moderator Chiroone's Avatar
    Join Date
    Feb 2004
    Posts
    1,121
    Feedback Score
    5 (100%)

    Default

    I received my EP lower yesterday and the take down pin hole is too high, maybe to far forward also, not sure how much of and issue it will be. I guess I will have to egg out hole and fill with some JB weld or some other filler. Not exactly what I expected, but for $35, I guess you get what you pay for.

    Nemo ME Impune Lacessit
    Manus sapiens potens est
    пиштоли не убиваат луѓе, тие само го прават тоа полесно

  8. #148
    Always sore, always tired Bradrock's Avatar
    Join Date
    Feb 2005
    Location
    Missouri/ Ark border
    Posts
    6,087
    Feedback Score
    23 (100%)

    Default

    This may be a stupid idea. But if the countersunk area of the off center pin hole is correct location. Could you clean out that area & make a press fit bushing from brass or nylon to insert ?
    " Save a tree...........Eat A Beaver!"

  9. #149
    AKAHOLIC o.d. ak's Avatar
    Join Date
    Jul 2006
    Location
    South West Missouri
    Posts
    1,584
    Feedback Score
    3 (100%)

    Default

    Quote Originally Posted by Chiroone View Post
    I received my EP lower yesterday and the take down pin hole is too high, maybe to far forward also, not sure how much of and issue it will be. I guess I will have to egg out hole and fill with some JB weld or some other filler. Not exactly what I expected, but for $35, I guess you get what you pay for.

    Quote Originally Posted by Bradrock View Post
    This may be a stupid idea. But if the countersunk area of the off center pin hole is correct location. Could you clean out that area & make a press fit bushing from brass or nylon to insert ?
    Check fit with an upper or two before you make any more holes or adjustment. Mine looks just like your but when I put my upper on the holes line up nearly 100% between the lower and the upper, the countersunk area is the part that is off.

    Looks like on mine all I will have to do is open the countersunk area a little larger to get the takedown pin to seat all the way.

  10. #150
    3/6 Infantry mtdew's Avatar
    Join Date
    Jul 2005
    Location
    Benton,AR
    Posts
    2,782
    Feedback Score
    3 (100%)

    Default

    Quote Originally Posted by Chiroone View Post
    Dew,

    Which one of the XY cross tables did you get a Grizzly?
    I got this one. http://www.grizzly.com/products/Cros...ing-Vise/G1064 $57.90 after s&h. You still have to clean off the grease and grit, Adjust gibs to take up the play, and lube. I like it.
    "NA BEAN DON CHAT GUN LAMHAINN"
    Clan MacPherson
    "CREAG DHUBH"!

Page 15 of 24 FirstFirst ... 5 11 12 13 14 15 16 17 18 19 ... LastLast

Search tags for this page

80 polymer
,

polymer 80

,

polymer 80 blem sale

,
polymer 80 lower review
,
polymer 80 lowers on sale
,
polymer 80 sale missouri
,

polymer lowers breaking

Click on a term to search our site for related topics.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •