Page 16 of 24 FirstFirst ... 6 12 13 14 15 16 17 18 19 20 ... LastLast
Results 151 to 160 of 233

Thread: Polymer 80% lowers

  1. #151
    Moderator Chiroone's Avatar
    Join Date
    Feb 2004
    Posts
    1,018
    Feedback Score
    5 (100%)

    Default

    Dew,

    That is a good price and cheaper than HF even with shipping. Travel a bit short at 4" but plenty for an 80% AR receiver. Have you used it as yet in actual "milling"?
    Nemo ME Impune Lacessit
    Manus sapiens potens est
    пиштоли не убиваат луѓе, тие само го прават тоа полесно

  2. #152
    3/6 Infantry mtdew's Avatar
    Join Date
    Jul 2005
    Location
    Benton,AR
    Posts
    2,686
    Feedback Score
    3 (100%)

    Default

    Just checked tracking on my end mill. Its sitting at home now so I might try it tonite.
    "NA BEAN DON CHAT GUN LAMHAINN"
    Clan MacPherson
    "CREAG DHUBH"!

  3. #153
    Moderator Chiroone's Avatar
    Join Date
    Feb 2004
    Posts
    1,018
    Feedback Score
    5 (100%)

    Default

    Good Luck let me know how it goes.

    BTW, I heard from EP Lowers today regarding my inquiry on the placement of the take down pin hole, here is the response:

    The recessed areas of the take down is off but the hole is in the correct placement for the pin insertions.
    Thanks
    Nemo ME Impune Lacessit
    Manus sapiens potens est
    пиштоли не убиваат луѓе, тие само го прават тоа полесно

  4. #154
    Gunco Member dunn6902's Avatar
    Join Date
    Nov 2007
    Posts
    173
    Feedback Score
    7 (100%)

    Default

    If they intended for a .025 gap between reciever halves and having a rear pin that needs a hammer to remove then yes,it's in the right location.

  5. #155
    Moderator Chiroone's Avatar
    Join Date
    Feb 2004
    Posts
    1,018
    Feedback Score
    5 (100%)

    Default

    Well, I did not exactly buy it either, but I think their embarrassment must be high right now because even the non blems seem to have this issue. Maybe a design flaw in the molding process
    Nemo ME Impune Lacessit
    Manus sapiens potens est
    пиштоли не убиваат луѓе, тие само го прават тоа полесно

  6. #156
    aka: SDK1968 dutigaf's Avatar
    Join Date
    May 2006
    Posts
    3,754
    Feedback Score
    14 (100%)

    Default

    got the notice from P80 today.... they have shipped.
    say what you mean & mean what you say


  7. #157
    3/6 Infantry mtdew's Avatar
    Join Date
    Jul 2005
    Location
    Benton,AR
    Posts
    2,686
    Feedback Score
    3 (100%)

    Default

    Makin' chips. It came out real nice, albeit alot slower than using the dremel like I did on the first one, as I have no real experience with milling. But thru trial and error I figured it out. Its real handy for drilling the holes accurately.
    Attached Images Attached Images
    "NA BEAN DON CHAT GUN LAMHAINN"
    Clan MacPherson
    "CREAG DHUBH"!

  8. #158
    aka: SDK1968 dutigaf's Avatar
    Join Date
    May 2006
    Posts
    3,754
    Feedback Score
    14 (100%)

    Default

    heh heh...

    yeah bud if your a garage builder like you or me.... a mill is just a big drill press that has not bit wobble. LMAO
    say what you mean & mean what you say


  9. #159
    GuncoHolic Sprat's Avatar
    Join Date
    Feb 2005
    Location
    Florida
    Posts
    3,574
    Feedback Score
    4 (100%)

    Default

    range report

    finally I got a break to hit the range today, shot a couple of boxes of blemished 223 reloads, everything worked fine except for the aftermarket mags( 11 round bulgarian polymer Ar mags) I used, once I switched to USGI used mags, the complete unit functioned real good as I expected it would

    so for those concerned the 80% blem lower pictured above, that is now 100% functioned flawlessly
    Sprat and sprat1 are one and the same.

  10. #160
    3/6 Infantry mtdew's Avatar
    Join Date
    Jul 2005
    Location
    Benton,AR
    Posts
    2,686
    Feedback Score
    3 (100%)

    Default

    Maybe I'll get me one of them fancy milling machines one of these days...
    "NA BEAN DON CHAT GUN LAMHAINN"
    Clan MacPherson
    "CREAG DHUBH"!

Page 16 of 24 FirstFirst ... 6 12 13 14 15 16 17 18 19 20 ... LastLast

Search tags for this page

80 polymer
,

polymer 80

,

polymer 80 blem sale

,
polymer 80 sale missouri
,

polymer lowers breaking

Click on a term to search our site for related topics.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •