Page 8 of 25 FirstFirst ... 4 5 6 7 8 9 10 11 12 18 ... LastLast
Results 71 to 80 of 248

Thread: RPD Build Run

  1. #71
    Cetme Junkie cetme1223's Avatar
    Join Date
    Feb 2011
    Location
    Wisconsin
    Posts
    27
    Feedback Score
    0

    Default

    Ok sounds great just wanted to be sure I wasn't missing something. Thanks again for all your help!

  2. #72
    Gunco Rookie SimonovsDog's Avatar
    Join Date
    Mar 2005
    Location
    N. Mississippi
    Posts
    13
    Feedback Score
    0

    Default

    You're doing an awesome job Pirate. Take your time, and keep up the great work!
    D.L. Cooper

  3. #73
    Administrator pirate56's Avatar
    Join Date
    Dec 2004
    Posts
    4,996
    Feedback Score
    31 (100%)

    Default

    I got all the GI Barreled shortys done today. 2 of them have 5/8" x 24 threads on them, they are marked with the red dye. They will accept the adapters for a silencer.

    I have one super shorty to do, the barrel is almost done and I will finish that up tomorrow.

    The next step will be to pull the kits, install the firing pin extensions, fit the feed trays and feed covers and pull out the lowers and mark them to get ready to start machining them.
    Attached Thumbnails Attached Thumbnails RPD Build Run-dsc01162.jpg  

    RPD Build Run-dsc01163.jpg  

    RPD Build Run-dsc01165.jpg  

    RPD Build Run-dsc01166.jpg  

    RPD Build Run-dsc01164.jpg  


  4. #74
    Gunco Regular voland's Avatar
    Join Date
    May 2005
    Posts
    401
    Feedback Score
    11 (100%)

    Default

    Would you consider offering a service for cutting the extractor relief on US me barrels. I have three that need the cut made.

  5. #75
    Administrator pirate56's Avatar
    Join Date
    Dec 2004
    Posts
    4,996
    Feedback Score
    31 (100%)

    Default

    Quote Originally Posted by voland View Post
    Would you consider offering a service for cutting the extractor relief on US me barrels. I have three that need the cut made.

    I have a special cutter for it. It is $50.00 a barrel, if you have 3 I will do it for $120.00

    Keep in mind I am in the middle of building 26 guns and can't stop what I am doing till these guns are out the door.

  6. #76
    Gunco Member THECARREAPER's Avatar
    Join Date
    Mar 2011
    Posts
    93
    Feedback Score
    0

    Default

    Quote Originally Posted by cetme1223 View Post
    So when is the last part of the payment due for the standard builds?


    Quote Originally Posted by pirate56 View Post
    when the guns are done, we are still a long way off from being done. after I get the 6 shorty barrels done it will be time to start machining the lowers. there are several operations on them and they take a long time.






    Sorry Stan, I sent the balance of my payment in full with the DPM receiver and mags.

    Did not mean to mess up the process, but I am on the list for a Semi Bren, a semi DPM and hope fully a semi Gory SG46 , (if you build Gorys later)

    Just wanted to show I was sincere, and put my money where my orders are!


    I will send a primary and back up FFL to you soon.


    Thanks again for all your hard work.

  7. #77
    Administrator pirate56's Avatar
    Join Date
    Dec 2004
    Posts
    4,996
    Feedback Score
    31 (100%)

    Default

    I am getting near the end of the first phase of this run. At the end of the day today I got in all the firing pin extensions, fitted all the feed trays and feed covers, installed the front sights on the us barreled guns and drilled the gas ports. I got the super shorty barrel installed and the receiver parts fitted up on it as well.

    Tomorrow I will install the front sights on the shorty's and that will complete the receiver assembly operations. The lowers are all pulled out of the kits and marked and ready to start machining them next week.
    Attached Thumbnails Attached Thumbnails RPD Build Run-dsc01167.jpg  

    RPD Build Run-dsc01168.jpg  

    RPD Build Run-dsc01169.jpg  

    RPD Build Run-dsc01170.jpg  

    RPD Build Run-dsc01171.jpg  

    RPD Build Run-dsc01172.jpg  


  8. #78
    Administrator pirate56's Avatar
    Join Date
    Dec 2004
    Posts
    4,996
    Feedback Score
    31 (100%)

    Default

    here are a few more photos
    Attached Thumbnails Attached Thumbnails RPD Build Run-dsc01173.jpg  

    RPD Build Run-dsc01174.jpg  

    RPD Build Run-dsc01175.jpg  


  9. #79
    Gunco Member THECARREAPER's Avatar
    Join Date
    Mar 2011
    Posts
    93
    Feedback Score
    0

    Default

    wow, breathtaking!

  10. #80
    Gunco Rookie SSG3K's Avatar
    Join Date
    Mar 2011
    Posts
    8
    Feedback Score
    0

    Default

    This is pretty cool. I have participated in alot of build programs but nobody has ever done this before. Great job!

    Rich

Page 8 of 25 FirstFirst ... 4 5 6 7 8 9 10 11 12 18 ... LastLast

Search tags for this page

There are currently no search engine referrals.
Click on a term to search our site for related topics.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •