View Full Version : Help with FAL build
07-06-2008, 01:20 AM
I just bought 4 barrels and 4 DCI receivers. I have tried every barrel on every receiver and each will tighten to about the 9-10 oclock postion. I am unable to get any of them to the 12 oclock postion.
If I back them each off I get a nice gap between the receiver and barrel face. Any ideas how I can get these mounted correctly??
There must be a solution. If I use a big washer then I have a large gap in my breech.
I need advise on this one.
07-06-2008, 02:00 AM
I will help you out with these. Call me
07-06-2008, 03:32 PM
if they go to far you need to shim the bbl sholder, if they don't go far enough you need to trim the bbl shoulder.
07-06-2008, 06:08 PM
Sounds like inch barrels and metric receivers.
07-06-2008, 07:47 PM
Hey here is a site where a guys used an grinding pad put over and up to shoulder of the barrel
and spins it by hand to take off a little at a time until the barrel clocks to 11 oclock position
here is the link WECSOG.org - "Texas Jungle" Carbine Build (http://wecsog.org/fal/carbine/)
07-06-2008, 10:00 PM
You can either trim the barrel shoulder or trim the fwd face of the receiver
07-10-2008, 11:42 AM
Not an uncommon problem.
Easy way to trim, if you don't have a lathe, but access to full size drill press. Take off the flash suppressor. Put the muzzle in the chuck and center it. Use a slow speed spindle on the pulley system. Using an abrasive disk from a grinding disk with the open spindle hole, grind of small amounts of the facing. Check fit often. If you take off too much, you will need a barrel index bushing. Check with James, the Gun Parts Guy. he usually has them. Gun Parts Guy - Military Surplus Gun Parts FN FAL L1A1 (http://www.gunpartsguy.com/)
Good luck on the build!
08-03-2008, 12:38 PM
I barrel these at my shop all the time. Contact me at: email@example.com
08-15-2008, 12:49 AM
Sledgehammer, another name I recognize.
08-15-2008, 08:48 AM
First make sure that the barrel is not bottoming out inside the receiver.
Remove the material from the barrel shoulder VERY slowly. You will be amazed how little it takes to go from 9 O'clock to 12 O'clock. It will only take a couple of thousandths
08-15-2008, 10:48 AM
Trim until it goes on hand tight to about 10:30 to 11 O'clock at most. That's my method with 15 builds so far. It will go the rest of the way to top dead center once you put the wrench on it. Go slow as 7.62x39 said. Metal removed can't be put back and you don't need to remove much if you're already at 9 O'clock.
I sandwich a piece of emory cloth between the barrel and the old receiver stub to remove metal from the barrel shoulder. The stub keeps the sand paper flat for even removal all around. Simply work the paper back and forth.
So who has DCI FAL receivers for sale now?
08-16-2008, 08:02 PM
what retvet said..... OR send it to SALBO Arms.....hehehe
08-23-2008, 10:08 PM
Had that issue. File and check, file and check. Even when it looks like it is bottoming out on the receiver you have a bit more room to go. Like 7.62 says, you really don't have to remove much material. I used a file on the shoulder and took my time.
01-17-2009, 02:07 AM
I have even used jewelers files. As retvet said" take your time " thats part of the learning how to build these things and it pays off in the long run.And soon you'll be
helping someone else learn this addicting habbit.