I built 7 firearms in one afternoon
Well sorta, at least in the eyes of alphabet guy's.
I received Stitckerman's bending jig Friday, so I spent yesterday afternoon bending up 7 flats.
6 Tapco's and 1 FAC I've had hanging around for a while. All 7 came out perfect.
Stickermans jig does a fabulous job bending these flats, however setting them up is a royal pain in the kiester.
Setting them up by measuring is very time consuming and frustrating (have you ever tried to move something .002?)
On top of that, once you finally have it perfect, it changes when you tighten the plate.
After doing the first 3 by measurement, I decided to drill the jig to use locating pins.
After carefully locating a flat, I drilled the jig center piece for pins, what a relief, the last 4 went very quickly, and were right on the money.
Bending 7 flats, does not make me an expert on the subject, but I have a couple of observations as a guy whose been there, done that.
After seeing how much force is required to start the initial bend, I'm very leary of DPH's new jig base design,
His die looks very robust, even more so than stickermans, (although his works perfectly) but the base concerns me.
I would be afraid that the angle iron would tend to splay after a few bends, it appears to be only 1/4" stock, and with those huge notches on either end, there is nothing to hold the two sides parallel.
I don't know this as fact, it's pure speculation on my part.
Judging by how hard I worked my press, I would say it takes at least a couple of tons of pressure to start the bend.
I do like their full height center section, and that it's threaded instead of having to fumble with nuts.
I'm not sure why stickerman does not have locating pins on the jig itself. There are a couple of undersized pin holes on the bottom plate to get you in the ballpark, but man, it's a big freakin park when you're working in thousandths.
I know both of these are new products, and will certainly be refined as time and experience go on, both are proven performers.
But as they sit right now, I would say the ultimate bender would be DPH's die in stickermans base.
Good post and I'm so glad to hear I'm not the only one that has a hard time centering these flats!!
max how do you bend the top rails with stickmans jig.those flats you bent look great.also what will you do for heat treat? great job! rick
I start the upper rail bend with a super high tech tool I designed. lol
Originally Posted by mike
I ground and polished the head of a H-D head bolt, it works good to get the bend started.
Then I use a hammer and a block of steel to finish the bend.
I have a Mapp/Oxy torch for heat treating.
Originally Posted by 7.62x39
Like the idea of dual purpose use, so is that a shovel head or a evo head bolt?
Shovel, but a panhead or even a knuckle would work fine.
Originally Posted by Chiroone
Evo's don't have headbolts, they use studs
Yeeehaaaaaa Christmas day at last.....got my flat bending jig from Stickerman today. Its a good piece of work and Ill buy another tomorow if I needed one. All I need is my press to get here and Im rolling. Thanks Curtis.
So , as I understand it, you drilled two 1/8" holes in the die in the areas of the alignment holes on the flats and then put two roll pins in them. Is that about right?
More or less.
Originally Posted by Chiroone
The pin holes in the flats are .120 I opened them up to 1/8" (.125)
Drilled two .125 holes in the center section about .500 deep, opened up the holes in the plate to .125
Then used two 1/8" drill bits to align the flat while I tightened the the plate.
Then removed the bits.
The plate locks the flat in place nicely, so the pins are only needed for alignment.
That's the kind of feedback I wanted to hear. I'll make some changes on the next ones. Threading the holes instead of using nuts will take longer to make though. Maybe just tack welding the nuts on would work?
The pins I sent were .1093" and the holes in the flats are .120" I have a piece or two of .120" drill blank and the right bit so I'll try one to see if it centers up right on the two flats I haven't bent yet.
It's nice to see pictures that somebody else has taken of the one I built