10-25-2010, 11:20 PM
Here is picture of the 3.5" 20ga brass case in
FBW falling block. Nice cases by RMC.Shotgun primer.
Using 395 gr sabot get over 2700 fps. 600gr
over 2200. Cases take many reloads with
minimum sizing. One fired 8 times, still good
and the slower powders get the velocity
without the hard shock to cases, compared to
fast shotgun powders. And the hotrod Hastings
factory loads work in the gun also.
Guy got new design 8 and 10 ga slugs with
bigger hollow in the base. 1100gr for 8 and
900gr for 10. More accurate in smooth bores.
Will let everyone know when he is ready to
make a few for shooters.Ed
11-04-2010, 01:21 PM
I like singleshot break actions. I found another brand that will work
to make heavy barrel 12 and 20 ga FH. By monoblocking in heavy
barrels. It is the CBC Model SB. It has stock mounted like more
expensive doubles and O/U. And nice shaped pistol grip stock.
They have the nice stylish look like the Win 37 and Stevens 94.
But they are heavier built, just need heavy barrel.
I going to do a couple by monoblocking in heavy barrels, one 20ga
and one my 585 HE like I did in the NEF.And they are 50 to 100 bucks.
That action is a 1/8 inch wider than NEF, has big breach diameter
like NEF 10/12 gauges. The bearing surfaces on the pivot is .300"
wider, and pivot block is 1/4" wider. Pivot pin is 1/10" bigger.
The action is a 1/2 inch taller, and extra diameter at breach end.
In fact you could build a real hairy 8ga on its wider action, with
a heavy barrel and a new pivot block welded on.Ed
11-07-2010, 01:01 AM
More info on doing 20ga 3.5" in break actions. Nice
to do them in falling blocks, but they aren't available
for decent price. One choice, heavy barrel NEF 20ga,
lengthen chamber, but barrels are too short for proper
burning of large loads. Longer barrel better and helps
with recoil. And in a break action looks better to me.
Brass cases from RMC 7 bucks, decent price compared to
600NE brass at twice that. Many guys want 20s along with
the bigger. So you put a heavy barrel in a gun like the CBC
which is low cost and put extra toward the barrel.
Which is why I started research after getting a CBC,
as it is about perfect for the 20ga added heavy barrel.
Or in NEF, a little more. Or other singles, if heavy enough.
And you still fire factory 3-3.5" slug loads. And 3.5" brass
20ga will do same as 600NE factory loads, in a gun at
1/20 the price. That is reason we are looking at monoblocking
20ga barrels to make heavy strong guns, that can
get great velocities, less cost.. Like 600gr to 2200 or more.
Added heavy barrels in right actions will hold all the
pressure the RMC brass operates at. And remember one
experimenter has 20ga kills at 160 and 230 yds on deer.ED
11-12-2010, 05:52 AM
More info on 10 and 8 gauge slugs. The guy got some
made with deep hollowbase, 10ga 900gr, 8ga 1100gr.
He will make them for a buck each.
Bob Bigando in AZ. (bobiano at yahoo.com)
Good price as they are nice hard shiny slugs.
For seals for 10 and 8 gauge you can get regular
card seals and nitro fiber wads, but plastic seals
will do better, about a 100 fps in the faster loads.
Plastic seals for 10 ga are at BPI, called - X10X.
For 8ga I cut bottom seal part off of the 8ga wadcup
that BPI has. For extended accuracy in smooth bores
you can screw the seals on to the slugs and that
will make the overall projectile more front heavy.
Or better yet screw nitro fiber wads to the slug,
like the Brenekkes are. Good smoothbore accuracy
Use slugs with seals on, with slower RE17 that fills
case so no fiber wads are need.Just seal and slug.ED
11-29-2010, 04:32 AM
I talked about these 12ga jacketed full bore slugs earlier,
shown below. Well now BPI has something similiar in
their new catalog. We have tested some and one guy
got a 3 shot group that is nearly touching at 50 yds
in a scoped NEF Ultra slug gun. They can go real fast in
our 3.5 RMC or our real long case.They are hollowpoint
and fairly streamlined.I fill them with plastic glue for
better streamlining.Fullbore and no sabots needed.
Relatively light weight, to lessen recoil.Ed
12-16-2010, 04:55 AM
The 12ga Brenekke slugs with locked on base and the USS-S
slugs I test have led to other combinations that I've put
together using different slugs and wads. The object is
60 yd accurate, economical slugs for reloading smoothbores
that in the reloading process we can get more power also.
Like the Lyman cast slugs in thickwall 10ga steel wads,
with the slug glued in and wad cut off even with top of slug.
Then with wad cut even, you load and can rollcrimp perfect.
It makes a real nose heavy combination that is as accurate
in smoothbores, as the expensive 10ga foster style slugs.
Another one is the hollowbase 577 soft lead slugs that Dixie
sells, I put in a thickwall 16ga wad that BPI has. I glue it in
using Goop, a thick glue that hardwares sell. Epoxy works.
Another one is 20ga ga thickwall wad with 54 cal hollowbase
soft lead slugs. All these and others can be loaded for a fifth of
factory for smoothbores, and be as accurate as foster slugs.
And our slow powder loads seal good with wadcups.
Representative one in middlle, 10ga.Slug glued in tight.Ed
12-27-2010, 06:04 AM
Some wonder if only trying for foster slug accuracy at 200 feet
or 60-70 yds wasn't the best goal in a smooth bore, But if you get it
at 20% of the cost you've made a big gain. And most deer here are
killed at 30 yards. And putting slugs inside of thickwall wadcups,
with corresponding nitro wads under slug to get slug to the front
of cup, slug glued in, makes them long and a little more accurate than
foster slugs. Reason is the forcing cone in smoothbores. With the
long nose, heavy combination of wadcup/slug, the back of the
wadcup is in case yet while the front gets into the bore, past the
forcing cone, for a straight start. Little better accuracy. Like the
accurate US-S smoothbore locked on base slug, that is long.
The longer the nose heavy slug/sabot combo is, the truer it flies.
And most of these combinations work in brass cases with
thick walls like RMC cases. They fit real tight for my cases. Ed
01-12-2011, 05:04 AM
Penetration with slugs-Had a bunch of
wood blocks up to 12" through.
20ga load is a 54 cal 410 gr slug glued in wadcup.
Gives the same effect as Brenekke with locked on base..
Good in smoothbore at 50 yds.Goes through
6" block of wood easy/
Buckshot load in 4bore, 9 140gr 45cal balls at 1800,
all zip through 3/4" OSB and keep going.
In 4bore 760gr steel ball zips through 12" block of wood.
going over 3200 fps. Wood is dried hard poplar.
In 10ga 3.5" plastic case, a 900gr hardcast slug at 1800
fps, through same kind of block easy. This slug I put
on a screwed on base with plastic seal and wad.
I've also put plastic seals and fiber wads on 8ga
slugs to test later..
12ga 600gr hard slug at 2100 zips through 12"
wood block like it was putty.In a 3.5" RMC
case in NEF.
Anyone wanting one of my loaded 585HSMs to
collect or look at, let me know. 750gr
slug in this at 2800 in Enfield test gun.
Soon have barrel in PH and put the real
speed to it. About 33-3400.
Will soon have the heavy 20 ga barrel mono-blocked
into the 12ga barrel setup on the CBC break action.
Make a nice looking gun. Also going to put the 8ga heavy
barrel I had in Enfield for testing into falling block
built like the 4 bore one.Maybe done by summer.
Will be in one piece stock like 4bore.Ed
01-16-2011, 03:41 AM
Finding real slow powders that works with shotgun primers,
without starter powder. We found RE-17 and surplus 7383.
To recap faster rifle powders we use -VV110,IMR 4759,4227..
On the thread we've written about real slow powders like
H-BMG we've used with a starter powder, IE 15gr of Blue dot,
and H-BMG in amounts from 150 gr to 230gr in 3.5 and 3.85
inch brass cases. And 3.5 " plastic cases. 860-1040 gr slugs.
Tested in NEF with long heavy barrel.
We finally got some RE-50,a really slow powder like H-BMG.
It works with a real magnum shotgun primer with heavy slugs,
860 gr on up, in 3.5" RMC brass, 3.5" plastic and our long
brass case. I used 239 Fed primers. Lighter slugs
only give squib loads.RE-50 Is a powder made like RE-17
with the deterrant all through the grain of the powder,
rather than all on the surface of the grains, so it will ignite
easier, to get the initial combustion started.
In brass case used 240gr with 860gr slug, 1950 fps
and 220gr with 1040gr slug, 1750.
In 3.5" plastic 860gr slug with 180gr RE-50, 1500 plus.
Now these velocities aren't earth shattering as powder is real
slow, but cases don't expand, not even plastic case base cup.
And no starter powder. Nice thing is just fill cases
leaving room for slug and seal and no worries about
to high of peak pressures with heavy slugs
or cases expanding to stick.
Now to get 239 primers get Fed 12ga long red
3.5" primed cases from BPI. I used Fed cases,and took out
primers and used in other plastic and the brass cases.
Some guys trying to free up 239 primers for us reloaders.
Federal puts them in 3.5" mag 12ga loads and 10ga cases.
Elsewhere it was reported someone may do a 16ga sabot.
Also a guy got huge antlered buck with hotrod 20ga. Ed
01-16-2011, 10:03 AM
Ed, have you tried black powder? The pressure curve is slower than smokeless, and it's much easier to light off.
Originally Posted by hubel458
I know it's messy and smoky, but it might be worth a try.