Gunco Forums banner
Cancel

.30 HEAVY BARREL BLANK CHOOSE CHAMBER.

707 Views 9 Replies 5 Participants Last post by  1biggun, 
1biggun
4
A 20" MEDIUM HEAVY BARREL BLANK IT IS CURRENTLY UNCHAMBERD BUT I WILL OR CAN BE CHAMBERD IT IN 7.62X25, 7.62X39 (.308 BORE) OR 300 SAVAGE. THIS IS A NICE BLANK THE STUB IS 1.044 IT WILL LIKELY WORK ON MANY BOLT ACTIONS LIKE MAUSER, WIN, RUGER, MOSIN NAGANT.

IT WILL MAKE A REALLY NICE TARGET BARREL FOR A AK AND THAT IS WHAT I INTENDED IT FOR. THE BARREL IS .918 AT THE EDGE OF THE TAPE BY THE BREACH AND THE MUZZEL IS .665.

THIS BARREL WAS SLATED FOR ONE OF MY PERSONAL TARGET BUILDS. iT IS A QUALITY BARREL AND WAS NOT FIRED. I EXPECT IT TO BE VERY ACCURATE.

DUE TO A BANKING ERROR I NEED TO SELL SOME STUFF FAST TO PAY PEOPLE I OWE.

IM ASKING $90 PLUS SHIPPNG CHAMBERD IN YOUR CHOICE OF 7.62X25, 7.62X39, OR 300 SAVAGE. I CAN CHAMBER IT TO YOUR CASE PROTRUSION SPECS OR DEEP CHAMBER IT SO YOU CNA TRIM THE BREACH FACE TO YOUR NEEDS. ADDITIONAL PROFILING CAN BE DONE FOR EXTRA.

I WOULD PERFER PAYPAL AS I NEED MONEY FAST. IST ILL TAKE IT GETS IT. I WILL ENTERTAIN REASONABLE OFFERS.

THE BARREL IS HEAVIER THAN A REMINGTON OR WIN MAGNUM PROFILE I PUT TAPE ON THE BARREL TO MARK THE DIAMITERS. EXCEPT THE STUB THE BARREL IS BLUED

I ALSO HAVE SOME 243 20" STD REMINGTON PROFILE BARRELS THAT CAN BE PROFILED FOR AK CONVERSIONS WITH PROPER LOADS IF ANY ONE IS INTERESTED PM OR EMAIL ME.

Attachments

See less See more
Save
Like
Status
Not open for further replies.
1 - 10 of 10 Posts
E
can it be chambered in x54r?
Save
Like
alpine44
Hi 1biggun,

Is there enough "meat" to make an UZI barrel in x25 ? If you do not have an UZI barrel to measure the diameter of the flange, I will get you the dimension tomorrow.
Save
Like
D
Can it be threaded to fit a hungarian front trunion?
Save
Like
1biggun
the shank is over 1" so it will fit about any thing. I dont think I can thread it for a hungarian reciver with my equipment.

It likely will work for a UZI if you turn it down and thread it. I caan likely find a lighter blank to start with EMAIL your barrel dimensions

I dont have a 7.62x54 reamer but yes it could be chamberd to that if you had the reamer or rented one. keep in mind the bore is .308 and much of the x54R ammo is
.310 or so. there are a few x54 guns that came with .308 or .309 barrels. If you reload using 308 barrels this would be perfect for a heavy barrel set up. I may use it on a Mosin if it dont sell.
Save
Like
1biggun
reducing price. NOW $85 SHIPPED IN THE LOWER 48 STATES.
Save
Like
tanvil
1biggun, what is the rate of twist?
Save
Like
1biggun
Im guessing its a 1-10 ill confirm it tonight.
Save
Like
alpine44
Hi 1biggun,

If the barrel is at least .917" dia at 7.625" from the breach end, I'll take it with a chamber for 7.62x25. Chamber deep enough to have at least half of the extractor groove inside of the barrel. I will trim to correct headspace on my lathe.

Thanks,
alpine44
Save
Like
1biggun
it is under .917 at 7.625 form the breach end. you are going to almost need a straight no taper blank for that ore a really heavy varmint taper.
Save
Like
1 - 10 of 10 Posts
Status
Not open for further replies.
Gunco Forums
A forum community dedicated to AK-47 and AR-15 firearm owners and enthusiasts. Come join the discussion about optics, hunting, gunsmithing, styles, reviews, accessories, classifieds, and more!
Full Forum Listing
Explore Our Forums
Off Topic Lounge AK-47 Discussion Forum AK BIY forum General Firearms Discussion Jokes and Humor
Top