Ak-builder jig borrow.

3057 Views 25 Replies 12 Participants Last post by rigore, Oct 1, 2012

soumi

Discussion Starter · May 12, 2010

I have a new ak-builder flat bending die set that I won't be using for a while so I would like to let the members on gunco try it out for a few days so they can bend some flats , if you are having a build party that would be great

.

I only need $20 for shipping and if you want you can donate $5 to gunco. I also need an e-mail address , a phone number and the member must have at least 2 positive Itrader reports , this is all so I don't get the jig stolen from me. I will not write down or memorize your e-mail or phone number , I will keep it in the PM you send me and once the jig is returned I will delete the PM. If you have any questions or you need pictures of the jig I can help you with that

. The first one to say I'll take it gets it.

See less See more

1 - 20 of 26 Posts

rigore

· #2 · May 12, 2010

Very kind of you! I have to order some flats first.

Thanks.

Rev Jim Jones

· #3 · May 12, 2010

Very nice of you. HOWEVER, you really should bend your own flats first, as many of the loaner/rental tools don't have a very long life..or so it seems.

soumi

Discussion Starter · #4 · May 13, 2010

Rev Jim Jones said:
Very nice of you. HOWEVER, you really should bend your own flats first, as many of the loaner/rental tools don't have a very long life..or so it seems.

I already did

. But I can tell you one thing this jig takes so little pressure to do its job that you could probably (although I wouldn't recommend it) get it to bend flats with a door frame some 2x4s and a car screw jack :rofl:. Plus you can bend about a dozen flats within an hour and they are "The Best" perfectly coined and everything

zteknik

· #5 · May 13, 2010

soumi said:
I already did . But I can tell you one thing this jig takes so little pressure to do its job that you could probably (although I wouldn't recommend it) get it to bend flats with a door frame some 2x4s and a car screw jack :rofl:. Plus you can bend about a dozen flats within an hour and they are "The Best" perfectly coined and everything

ive used a bench vise and some c clamps
perfect everytime!!!

2ndAmendican

· #6 · May 14, 2010

Suomi, did you purchase the Yugo 1.5 mm inner die??

soumi

Discussion Starter · #7 · May 14, 2010

2ndAmendican said:
Suomi, did you purchase the Yugo 1.5 mm inner die??

No , sorry . I was going to later. I wish I could help you out with that.

2ndAmendican

· #8 · May 14, 2010

No problem. Just wondering with the new Yugo flats out there.

soumi

Discussion Starter · #9 · May 21, 2010

soumi said:
I have a new ak-builder flat bending die set that I won't be using for a while so I would like to let the members on gunco try it out for a few days so they can bend some flats , if you are having a build party that would be great .

I only need $20 for shipping and if you want you can donate $5 to gunco. I also need an e-mail address , a phone number and the member must have at least 2 positive Itrader reports , this is all so I don't get the jig stolen from me. I will not write down or memorize your e-mail or phone number , I will keep it in the PM you send me and once the jig is returned I will delete the PM. If you have any questions or you need pictures of the jig I can help you with that . The first one to say I'll take it gets it.

Forget about the Itrader thing. If you want to borrow the jig I will still need your phone number and e-mail address

.

restoreit

· #10 · May 23, 2010

I will give it a try..Pat

soumi

Discussion Starter · #11 · May 25, 2010

restoreit said:
I will give it a try..Pat

pm sent

soumi

Discussion Starter · #12 · May 29, 2010

btt

soumi

Discussion Starter · #13 · May 30, 2010

pm sent

rigore

· #14 · Apr 22, 2011

Sending you a PM.

Racer 27

· #15 · Apr 26, 2011

I would like to rent this but I don't have enough posts to message you yet.

Vigil777

· #16 · May 12, 2011

Still available?
I need it for a polish underfolder flat.

Vigil777

· #17 · May 12, 2011

Quick question, Can you press a flat if the receiver rails are already installed?

rigore

· #18 · Sep 20, 2012

Sent you an e-mail to see if I can borrow the jig again.

Thanks.

Mr_Posthumous

· #19 · Sep 22, 2012

I'd like to borrow it if we could get the fixture to press yugo bulged flats.If I could get just that part, I'd even donate it.

sjohnson

· #20 · Sep 22, 2012

It's worth a call, I believe Curtis has sold the punch separately in the past.

1 - 20 of 26 Posts

This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.

Top